Tällä verkkosivustolla käytetään evästeitä parantamaan sivustoa ja paremman selailukokemuksen tarjoamiseksi. Jos valitset "jatka" tai jatkat sivuston selailua valintojasi muokkaamatta, suostut siihen, että käytämme evästeitä. Katso lisää evästekäytännöstämme ja evästeistä kieltäytymisestä klikkaamalla tästä

Economy Clips

The thermostatic head will be supplied, factory preset, with two economy clips. These economy clips are at first mounted to the right and to the left of the short information. These clips allow a variable

The thermostatic head will be supplied, factory preset, with two economy clips. These economy clips are at first mounted to the right and to the left of the short information. These clips allow a variable
marking,
limiting or
blocking
of an optimal temperature setting.The thermostatic head will be supplied, factory preset, with two economy clips. These economy clips are at first mounted to the right and to the left of the short information. These clips allow a variable
  • marking,
  • limiting or
  • blocking
of an optimal temperature setting.
Economy Economy
Fig. 1: pull back the economy clip Fig. 2: lift and remove the economy clip

Marking of a temperature setting 

(without limitation)

Upper marking of the temperature range

For this purpose pull back the red economy clip with your thumb up to the stop (please see fig.1), then lift and remove the economy clip (please see fig. 2). Thus, the thermostatic head can be turned and set to the desired temperature, e.g. index figure 3 = 20°C. Thereafter, the red economy clip must be inserted in the grooveto the right of the index figure 3 (please see fig. 3), then push the clip forward and afterwards pull it back to the stop with your thumb.

Lower marking of the temperature range

For this purpose the blue economy clip must be pulled back up to the stop with your thumb, then lift and remove the clip. The thermostatic head can now be turned to the desired temperature, e.g. moon symbol = 14°C. Thereafter, the blue economy clip is to be inserted in the groove to the left of the moon symbol (please see fig. 4), push the clip forward and pull it back with your thumb up to the stop.

Economy Economy Economy
Fig. 3:
red economy clip for upper marking/ limitation, e.g. 20°C
Fig. 4:
blue economy clip for lower marking/ limitation, e.g. 14°C
Fig. 5:
blocking, e.g. 20°C

Limiting of a Temperature Setting

Upper limiting of the temperature range

In this case the red economy clip must be pulled back up to the stop (please see fig. 1), lift and remove it (please see fig. 2). Then the thermostatic head can be turned to the desired temperature, e.g. index figure 3 = 20°C. Afterwards the red economy clip must be inserted in the groove right to the index figure 3 (please see fig. 3) and the clip pushed forward up to the stop.

Now every temperature setting up to the index figure 3 will be possible when turning the thermostatic head. Any temperature setting above the index figure 3 will be impossible.

Lower marking of the temperature range

For this purpose the blue economy clip must be pulled back with your thumb up to the stop, lift and remove the clip. The thermostatic head can now be turned and set to the desired temperature, e.g. moon symbol=14°C. Thereafter, the blue economy clip must be inserted left to the moon symbol (please see fig.4) and the clip be pushed forward up to the stop.

Now any temperature setting can only be made up to the moon symbol by turning the thermostatic head. Temperature settings which are below the moon symbol can only be made after removing the said limitation.

Removing the limitation

For this purpose, the corresponding economy clip must be pulled back up to the stop with your thumb. Any desired temperature setting can now be made.

Blocking of a temperature setting

For blocking a temperature setting both economy clips must be pulled back (please see fig. 1), the clips must be lifted and removed (please see fig. 2).

The thermostatic head must now be turned to the desired temperature setting, e.g. index-figure 3 = 20°C. Then the red economy clip is to be inserted in the groove right of the index figure 3 (please see fig. 5) and be pushed forward up to the stop. Thereafter theblue economy clip must be inserted in the groove leftof the index figure 3 (please see fig.5) and be pushed up to the stop. The thermostatic head cannot be deregulated in any direction.

Removing of the blocking.

For this purpose the red and the blue or, if need be, both economy clips must be pulled back up to the stop. Any desired temperature setting will now be possible again.